KUSHULENTERPRISES 5858e9f8b40a780a242d8ccc False 260 14
product image

LATICRETE® 290 Premium Floor and Wall Thin-set Adhesive

Products INR  0 INR  0
  • S
  • M
  • L
  • 1
  • 2
  • 3
Assured icon not found

LATICRETE® 290 Premium Floor and Wall Thin-set Adhesive PRODUCT DESCRIPTION LATICRETE® 290 Premium Floor and Wall Thin Set Adhesive is a high performance bagged cementitious powder to install ceramic tile, Vitrified tiles and natural stone using the thin-set method of installation. Application Designed for interior installation of ceramic tile, vitrified tile and natural stone for walls and floors. Can also be used for shaded balconies, podiums, verandas and terrace gardens which are not directly exposed to sun for most part of the day. *For all other exterior installation of tiles/stones with Laticrete® 290, use Laticrete® 73 /Laticrete® 4237/ Laticrete® 333 Admix instead of water. Advantages • Dual use: for both floors and walls • High bond strength • High Tack - Will hang tile without slippage •Easy to Use •Increased flexibility •Improved impact resistance Suitable Substrates • Concrete •Concrete masonry • Cement Mortar Beds •Cement Plaster • Vitrified Tile and Stones • Brick Masonry • Cement Terrazzo • Very large format tiles/ stones* *When mixed with LATICRETE® 73 Crete Amdix or Laticrete® 4237 High performance latex admix. Packaging – 20 kg & 50 kg bag Colour: Grey and White Coverage Approx 55-60 sft per 20kg bag with 1/4” x 1/4” (6mm x 6mm) square notch trowel Coverage will vary depending on trowel notch size, type and size of tile and substrate Shelf Life - Factory sealed bag of this product are guaranteed to be of first quality for one (1) year* if stored off the ground in a dry area. *High humidity will reduce the shelf life of bagged product. Limitations •Do not apply directly to plywood, chipboard, particleboard, decorative laminates or resilient flooring. •Do not install tile/stone when surface temperatures are below freezing point (32 °F / 0 °C). Always use LATICRETE® latex additives when temperatures approach freezing. •Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not designed as replacements for waterproof membranes. When a waterproof membrane is required, use a LATICRETE®9237 / Hydroban Waterproof Membrane. Note: Surfaces must be structurally sound, stable and rigid enough to support ceramic tile/vitrified tile/stone, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/vitrified tile/brick installations or L/480 for thin bed stone installations where L=span length. NOTE TO THE SPECIFIER AND INSTALLER: While installing tile/stone on the external walls and floors, we need to provide the movement joints by creating spaces between the tiles/stones and filling them up with cement based grout mixed with L1776 grout admix plus or silicone sealants. It is also important to note the following:  The exterior tile / stone installations are provided with joints (spaces) on the periphery of the area without allowing the tile / stone to be bound by the peripheral masonry work or plaster.  The tiles/stones must not be installed directly on expansion joints. The expansion joints need to be run through the tile / stone work till top surface and filled with materials which accommodate the movements. Cautions •Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water. •Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas. •Protect finished work from traffic or damage by other trades for an extended period of time during cold weather conditions. •Keep out of reach of children. TECHNICAL DATA Performance Properties LATICRETE® 290 Premium Floor and Wall Thin-Set Adhesive mixed with Water Applicable Standard • ANSI A118.1 – 1999; EN 12004, ISO 13007 Test Test Method Results Shear Bond Porcelain Tile, ANSI A118.1 – 1999; C-5.2.4 >256 psi (1.7 MPa) 28 day cure Shear Bond Porcelain Tile, Water immersion ANSI A118.1- 1999; C-5.2.3 >165 psi (1.1 MPa) Compressive Strength ANSI A118.4- 1999; F-6.1 (modified) >2550 psi (17.5 MPa) Complies with EN & ISO standard: C1 T E Complies with IS 15477 : Type 2 Adhesive LATICRETE® 290 Premium Floor and Wall Thin-Set Adhesive mixed with LATICRETE® 333 Super Flexible Latex Admix. Applicable Standard • ANSI A118.4 – 1999; EN 12004, ISO 13007 Test Test Method Results Shear Bond Porcelain Tile, 28 day cure ANSI A118.4- 1999; F-5.2.4 280 psi (1.9 MPa) Shear Bond Porcelain Tile, Water immersion ANSI A118.4- 1999; C-5.2.3 180 psi (1.2 MPa) Compressive Strength ANSI A118.4- 1999; F-.1 (modified) 4100 psi (28.3 MPa) Complies with EN& ISO standards : C2TE S1 Complies with IS 15477: Type 2 Adhesive Working Properties (70 F (21 C)) LATICRETE® 290 Premium Floor and Wall Thin-Set Adhesive Mixed with water Open Time Approx 20 minutes Pot Life 3 – 4 hours Time to Heavy Traffic 24 hours LATICRETE® 290 Premium Floor and Wall Thin-Set Adhesive mixed with LATICRETE® 333 Super Flexible Latex Admix. Open Time (21 °C) Approx 30 minutes Pot Life (21 °C) Approx 5 hours Time to Heavy Traffic 24 hours Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions. INSTALLATION Surface Preparation All surfaces should be between 40 °F (4°C) and 104 °F (40°C) and structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with LATICRETE® Latex Portland Cement underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. New concrete slabs shall be damp cured and 28 days* old before application. *No minimum cure time for concrete slabs when thin-set adhesive is mixed with latex additive. All slabs must be plumb and true to within ¼” (6mm) in 10 ft (3m). Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI Specification AN-3.8 “Requirements for Expansion Joints” or TCA Detail EJ171 “Expansion Joints”. Do not cover expansion joints with mortar. Cement Backer Board: follow TCA installation detail W244. Note: 1. Installer must verify that deflection under all live, dead and impact loads of interior plywood floors does not exceed industry standards of L/360 for ceramic tile and brick or L/480 for stone installations where L=span length; Mixing Stir LATICRETE® Admix thoroughly before use. Place clean, potable water or LATICRETE® latex admix into a clean pail. Add LATICRETE® 290 powder slowly in to the same pail. Use approximately 6 to 7 Liters of Laticrete® 333 or 5 to 6 Liters water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow adhesive to slake for 5- 10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel. Note: For improved bond strength, flexibility and for exterior installations use LATICRETE® 73 Crete Admix/ LATICRETE® 333 Super Flexible Admix. Application Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into wet, sticky adhesive and beat in using a beating block or rubber mallet to imbed tile and adjust level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. Grouting Grout installation after a minimum of 24 hours curing time at 70 F (21 C). Grout with LATICRETE® Sanded or Unsanded Grout mixed with LATICRETE® 1776 Grout Admix Plus. For maximum stain resistance use SpectraLOCK® Pro Premium OR LATAPOXY® SP-100 Stainfree Grout. Cold Weather Note: The setting of Portland cement adhesives and grouts are retarded by low temperatures. Protect finished work for an extended period when installing in cold weather. For faster setting adhesive use XTRABOND FSA 336 OR LATICRETE® 73 (Rapid) Crete admix with LATICRETE® 111 Crete filler powder. Do not set tile when surface temperature is below freezing point or when substrate is frozen. Hot Weather Note: The evaporation of moisture in Portland cement adhesives and grouts is accelerated by hot, dry conditions. Apply to dampened surfaces and protect freshly spread adhesive and finished work when installing in temperatures over40C. Cleaning Clean tools and tile work with water while adhesive is fresh. AVAILABILITY AND COST Availability LATICRETE® and LATAPOXY® materials are available worldwide. For distributor information: Telephone: +91-40-30413100 FAX: +91-40-23378784 e-mail: Cost Contact a LATICRETE® Distributor in your area. MAINTENANCE LATICRETE® and LATAPOXY® grouts require routine cleaning with neutral pH soap and water or MYK LATICRETE Clenza series suitable cleaners. All other LATICRETE® and LATAPOXY® materials require no maintenance but proper installation as per instruction. Performance and durability may depend on properly maintaining of Installed area. WARRANTY MYK Laticrete India Pvt Ltd warrants that LATICRETE®290 Premium Floor and Wall Thin-Set adhesive is free from manufacturing defects and will not break down, deteriorate or disintegrate under normal usage for a period of one(1) year from manufacturing of the product subject to the terms and conditions stated in LATICRETE® Product Warranty. TECHNICAL SERVICES Technical assistance Information is available by calling the MYK LATICRETE India Pvt Ltd

Availability: In Stock

Tags :

Billing Information

Order details QTY Total

Product Name 5b6b35c5277b75052ec872ba

Rs   2100

Note: Delivery usually takes 2.5 days, depending on availability and your location.
Order-Success icon not found

Your order has been placed successfully

Your order has been successfully placed. After it is reviewed, an email with the shipment details will be sent to the email ID you provided.
order-failure icon not found

Your order could not be placed

Your order not be placed. Please try again at a later time.