http://WWW.KUSHALENTERPRISES.NET
KUSHULENTERPRISES 5858e9f8b40a780a242d8ccc False 259 14
OK
background image not found
Found Update results for
'grout float'
9
PolyGlaze Tile Grout “PolyGlaze Tile Grout” is a white cement-based, polymermodified grout that produces hard dense joints that are resistant to shrinkage and cracking and can be used to fill tile joints on walls and floors with a minimum width of 1mm to a maximum width of 12 mm for both interior and exterior applications. Special Properties of “PolyGlaze Tile Grout”: Wide joint bridging. Good Water resistance – can be used both indoor and outdoor tile grouting. Excellent workability, smooth and easy to spread and easy clean-up. Exceptional color stability. Non-shrinking and high stain resistance. Being Polymer modified it enhances durability and helps to achieve a more robust, waterproof and flexible grout finish. Areas of use : “Polyglaze Tile Grout can be used in conjunction with Polyglaze Tile Adhesive (although not necessary) for grouting all types of Ceramic & Vitrified tiles, Mosaics, Porcelain, Quarry tiles, Bricks, Pavers, Slate and Natural stones. It may be used for interior and exterior- Floor, Wall and Ceilings. Being water resistant, Polyglaze Tile Grout can also be used for grouting wet areas like Swimming pools, power shower enclosures, etc. Surface Preparation : Ensure the tile adhesive has fully set before grouting. The surface should be clean, dry and free from dust, grease, oil, loose materials, adhesive residue and other contaminates. If required, clean the surface with a damp cloth or sponge. It is advisable to moisten the joints before applying the grout so as to assist the spread of the grout. Preparation of “PolyGlaze Tile Grout”: Take a small amount of water in a bucket and gradually add “Polyglaze Tile Grout”. Mix thoroughly in the ratio of approximately 3 parts of the product to 1 part of water by volume till a smooth paste is obtained. No further water should be added after final mixing. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. Protect the paste from direct sunlight, heat and use within 45 minutes of preparation. Application of “PolyGlaze Tile Grout”: After grout is mixed, use a rubber bottomed grout float to scoop the grout from the bucket. Then completely fill the tile joints with “Polyglaze Tile Grout” with the aid of a rubber grouting trowel diagonally without leaving any void or gaps. Work in small areas at a time. Remove excess grout from the surface as the work proceeds by drawing the float diagonally across the joints. When grouting external areas, protect during and after application. For Initial cleaning, allow 15 minutes for the grout to firm up before cleaning off excess with a damp sponge, rinsing the sponge frequently in between with water. The Final cleaning of the residual grout film on the surface of the tiles can be done using a clean dry cloth for buffing and polishing the tiles. Do’s about “PolyGlaze Tile Grout”: Ensure 24 hours time interval for grouting after tile fixing. For light traffic flow areas, allow grout to set for approximately 12 hours For best results, use spacers and keep a minimum of 2mm joints between the tiles. Don’ts about “PolyGlaze Tile Grout”: Don’t add too much water, it will weaken the grout. Don’t leave any excess moisture on the surface of the grout joints which may cause efflorescence on drying. Useful Tips : “Polyglaze Tile Grout” should be stored in a dry place. Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Color: “PolyGlaze Tile Grout” is available in choice of various colors. For details, please refer our shade card. Coverage : Approximate Coverage per 10 Kg.bag of “PolyGlaze Tile Grout” Tile Size 600x600x8mm 300x300x6mm 300x200x6mm 200x150x5mm 150x150x4mm 100x100x3mm Approx coverage 160 105 85 75 80 72 Note: Quantities shown are approximate and are given for estimating purposes only. Actual job site coverage’s may vary. It is always a good practice when calculating coverage to allow for 10-15% additional material for wastage and spillage. Technical Information: “PolyGlaze Tile Grout” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR White (Refer Shade Card for Color Options) PACKAGING 1 Kg & 500 gms Pouch STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 25 – 30% by weight POT LIFE Approx. 45 minutes TIME TO TRAFFIC Allow grout to set for 24 hours PERFORMANCE INFORMATION COMPRESSIVE STRENGTH > 4 N/mm2 after 7 Days FLEXURAL STRENGTH > 3 N/mm2 after 7 Days
PolyGlaze Tile Adhesive – Floor “PolyGlaze Tile Adhesive – Floor” is a cementitious readymix powder which is thin-bed and olymer modified product. Its unique properties make it ideal for fixing ceramic tiles, vitrified tiles, mosaic tiles and other floor tiles. Special Properties of “PolyGlaze Tile Adhesive - Floor” : Preparation is simple, just add water. Although cement based, requires no curing. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix floor tiles like ceramic, vitrified, mosaic and other floor tiles. Cementitious screeds. Cement Mortar beds. Bathrooms, kitchens etc. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure, prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – Floor”. Remove curing compounds, if any, from the surface. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - Floor”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – Floor” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - Floor”: Before fixing the tiles, clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - Floor”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – Floor” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left around each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive – Floor” is nonhazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze Tile Adhesive - Floor” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 45 – 55 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required Evershine Build India Private Limited HOME ABOUT US OUR PRODUCTS PolyGlaze Tile Adhesive – Floor PolyGlaze Tile Adhesive – XT PolyGlaze XT – Flex PolyGlaze White Tile Adhesive PolyGlaze Tile Grout PolyGlaze Jointing Mortar PolyGlaze Plaster PolyGlaze Wall Putty PolyGlaze Crack ‘O’ Fill PolyGlaze Repair Mortar EVENTS BRANDING OUR CLIENTELE CONTACT US Copyright © 2015 Evershine Build India Pvt Ltd
PolyGlaze Tile Adhesive – XT “PolyGlaze Tile Adhesive – XT” is a cementitious readymix powder which is thin-bed and a high tensile polymer modified product. Its unique properties make it ideal for fixing ceramic tiles / vitrified tiles /mosaic tiles / natural stones like granite, marble etc., to most building substrates. Special Properties of “PolyGlaze Tile Adhesive - XT” : Preparation is simple, just add water. Although cement based, requires no curing. It can be used in damp areas. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix wall and floor tiles, natural stones like granite, marble etc. Cementitious screeds. Cement Mortar beds. Bathrooms and kitchens. Fixing the facades. Swimming pools. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5 – 7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – XT”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - XT”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – XT” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - XT”: Before fixing the tiles, natural stones etc., clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes and before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - XT”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – XT” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left round each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive- XT” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “Polyglaze Tile Adhesive XT” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 60 – 70 sq.ft/ 20 kg bag @ 3 – 4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required
PolyGlaze White Tile Adhesive “PolyGlaze White Tile Adhesive” is a thin set, multipurpose, polymer fortified white adhesive offering vast utility including applications on interior floors & wall as well as limited exterior floor & wall installations. It can be used for fixing any porosity tile and natural stones like glass mosaic marble, granite on new / old substrates. Special Properties of PolyGaze White Tile Adhesive : It is ready to use mix; single component product, just add water in specified proportion and apply. High tensile adhesion strength. Being ready to use material, it saves considerable time and labour. Polymer modified formulation enhances its durability. Grouting is possible on the same day. Self-curing property helps in reducing shrinkage cracks. Recommended Substrate : Cement mortar bed. Ceramic tiles and Natural Stones – Walls & floors. Cement terrazzo Concrete Block. Application Procedure : Surface Preparation : The surface should be clean, dry and free from dust, grease/oil and other contaminants. As Polyglaze White Tile Adhesive is a thin set adhesive, be ensure that substrate surface is leveled to minimize the consumption. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze White Tile Adhesive”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fiber cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze White Tile Adhesive” : Take a small amount of water in a bucket and gradually add “PolyGlaze White Tile Adhesive” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done mechanically by stirrer or manually by hand. Mixing to be done till homogenous lump free mix is obtained. After mixing, leave the paste for 5-10 minutes for polymeric dispersion. The paste should be kept away from direct sunlight, heat and should be used within 30 minutes of preparation (after mixing with water). Application of “PolyGlaze White Tile Adhesive” : Before fixing the tiles, natural stones, etc., clean the backside of these with wet cloth to remove all dust and loose particles. Apply mortar to the substrate with the flat side of trowel, pressing firmly to work into surface. Comb on additional mortar with the notched side. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive from the face of the tiles. Any adjustment should be done within 20 – 30 minutes of application and before adhesive start hardening. Wait for at least 12 hours for the setting of tile adhesive before grouting. Caution : Store above the ground in Dry condition. During cold weather, protect the finished surface from traffic until fully set. Avoid contact with eyes or prolonged contact with skin. In case of irritation, rinse thoroughly with water. Keep out of reach of the children. Technical Information: “PolyGlaze White Tile Adhesive” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR White PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 30 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 55-60 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1 N/mm2 after 28 days SELF CURING Yes, no additional curing is required
PolyGlaze XT – Flex “PolyGlaze XT – Flex (Grey/White)” is a multipurpose cementitious ready-mix powder, which is thin-bed and a high tensile polymer modified product. Its unique properties make it ideal for fixing tiles & natural stones like granite, marble on plywood, metal surface and wall cladding. Special Properties of “PolyGlaze XT - Flex”: Ready to mix, single component product. Preparation is simple, just add water. Although cement based, requires no curing. It can be used in damp areas. Very high tensile adhesion strength. It is suitable for heavy duty application with moderate structural movements. It is suitable for fibre cement boards, wooden floor for both interior and exteriar surfaces. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix wall and floor tiles, natural stones like granite, marble on seasoned wood, metal surface, heavy duty applications like wall cladding at vertical surface. Cementitious screeds. Cement Mortar beds. Bathrooms and kitchens. Fixing the facades. Swimming pools. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow at least 4 weeks for concrete to cure prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze XT – Flex”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze XT - Flex”: Take a small amount of water in a bucket and gradually add “PolyGlaze XT – Flex” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 30 minutes of preparation (after mixing with water). Do’s about “PolyGlaze XT - Flex”: Before fixing the tiles, natural stones etc., clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 15-20 minutes and before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze XT - Flex”: Avoid very high speed mixing when electric mixing equipments are used. Coverage : 50 – 60 sq.ft per 20 Kg. bag with notch trowel for a bed of 3 – 4 mm thickness. Please note that coverage will depend upon the undulation of base substrate and thickness of material used. Useful Tips : “PolyGlaze XT – Flex” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left around each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze XT – Flex” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze XT - Flex” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey / White PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 30 minutes OPEN TIME 15 – 20 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48hours (depending on site conditions) COVERAGE 60 – 70 sq.ft/ 20 kg bag @ 3 – 4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH Approx>2 N/mm2 after 28 days SELF CURING Yes, no additional curing is required
Kushal Enterprises No.10 saroja complex sanathi street maduravoyal market chennai Near by murugan store Phone no 9884177503 Destibutor of poly glaze And laticrete tile adhesive wallputty epoxy grout cement grout and marble chemical etc materials
polyglaze tile epoxy grout 5.5kg
Myk laticrete and poly glaze tile adhesive floor thin set adhesive white flex white wallputty joint mortar cement grout plaster etc materials ableable here
PolyGlaze Jointing Mortar “PolyGlaze Jointing Mortar” is a thin bed, high strength, pre-mixed, quality assured mortar comprising of Ordinary Portland Cement, specially graded sand and Polymers. It is specially formulated and easily applied, giving a better bonding with higher air entraining properties. “PolyGlaze Jointing Mortar” is a masonry mortar for use in laying various types of fly ash / concrete bricks, AAC blocks and stones. It replaces conventional jointing mortar of 12-18 mm thickness with highly versatile 3-4 mm thickness mortar. Special Properties of “PolyGlaze Jointing Mortar”: Our quick setting proprietary mortar essentially “glues” the block together and the next course is ready to lay within a very short time. Higher bonding strength increases durability and eliminates future maintenance. Non-metallic, doesn’t rust out, will not discolor wall. Ready mixed mineral based products designed for new construction as well as for renovation purpose. Being premixed, it saves considerable time, labour and increases dimensional stability of the blocks. Being premixed and less porous, it inhibits efflorescence. Areas of use : Laying bricks and blocks: To join fly ash bricks, cement block, hollow blocks, aerated block etc. Jointing of prestressed concrete slabs, panels. Jointing of cement window and door frames. Barbecues and fire places. Garden and boundary walls. Screed and compost bins, sand pits. Bench stands, bicycle stands. Terracing. Ornamental Pools. Repairing of masonry walls. Surface Preparation : When laying new brick or block walls first construct a sound footing below the first line. All substrates should be cleaned and free from dust, oil, grease, curing agents, paints, which may affect adhesion. Wet the substrates before the application, without leaving excess water. When repairing mortar joints, remove all loose foreign materials. Preparation of “PolyGlaze Jointing Mortar”: Take a small amount of water in a bucket and gradually add “PolyGlaze Jointing Mortar” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water.). Application of “PolyGlaze Jointing Mortar”: Layout the wall you are going to work on and mark openings like door, windows, and any architectural appurtenances, you are including in your design. Put a thin layer of Jointing Mortar in the thickness of 3 to 4 mm on the clean and leveled surface using proper trowel on which the block work is to be carried out. Place the block on the laid jointing mortar in proper line and level. After placing the first block apply the jointing mortar of the same thickness i.e 3-4 mm for both horizontal and vertical joint of the block. Space “mortar boards” about every six feet along the wall, or on each side if the project is small. Brush the face of the brick with a foxtail brush to wipe away excess mortar and finish smoothing the joint. Continue laying the brick with 3-4mm thickness of jointing mortar until you are levelled with the leads you laid up. Filling the joint : Spread the mortar across the whole surface using the rubber blade of the trowel and work thoroughly into the joints. Brushing Off : After approximately 10-15 minutes, the mortar should have achieved a semi-dry consistency. Don’t brush this residual mortar into any unfilled joints. Useful Tips : It should be kept in dry place. Keep out of reach of children. Avoid inhalation of dust. Use proper tools while cutting blocks. Tools should be thoroughly cleaned in water to remove excess materials immediately after use. Technical Information: “PolyGlaze Jointing Mortar” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 40 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS Approx 25% by Weight POT LIFE Approx. 45 minutes HARD DRY 24 hours BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48hours (depending on site conditions) COVERAGE Approx 200 sq.ft/ 40 kg bag @ 3-4mm bed thickness (100mm AAC Blocks) PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH 0.60(MV)MPa as per ASTM D 4541 on Concrete block after 28 days 0.55(MV)MPa as per ASTM D 4541 on AAC block after 28 days COMPRESSIVE STRENGTH > 4 N/mm2 as per IS 4031 P.6 after 7 days FLEXURAL STRENGTH >5.5 N/mm2 as per ASTM C 580 after 3 days SELF CURING Yes, No additional Curing is required 14
1
false