http://WWW.KUSHALENTERPRISES.NET
KUSHULENTERPRISES 5858e9f8b40a780a242d8ccc False 257 14
OK
background image not found
Found Update results for
'new concrete slabs'
9
PolyGlaze Plaster “PolyGlaze Plaster” is a strong, durable pre-mixed powder suitable for plastering over all types of old or new conventional clay bricks, fly ash bricks/blocks and Autoclaved Aerated Concrete blocks(AAC). It is normally applied to masonry interiors and exteriors to achieve a smooth surface. Special Properties of “PolyGlaze Plaster”: Preparation is simple, just add water. Lighter than traditional cement- sand site mix mortar. Minimizes cracking and shrinkage free product. Prevents seepage of water. Fungus resistant. Non-toxic and non flammable. Durable & easy to apply. Saves both manpower and time. Being ready to use, it covers more work per day. Areas of Use: Under coating and plastering over existing concrete and brick/block walls. Use as a levelling plaster for correction of surface undulation in bare concrete block and other cementitious substrates. Basic levelling of concrete, light weight blocks and bricks. Filling holes and irregularities, levelling walls and ceilings. Create a leveled surface from uneven masonry or concrete wall. Surface Preparation : Dirt, soil, and roof runoff stains from the surface should be removed. Use a garden hose to loosen the dirt. Start at the top and wash the dirt down the wall. Proper hacking is to be done prior to application in concrete surface. Pre-wet the wall before application. Preparation of “PolyGlaze Plaster” : Take a small amount of water in a bucket and gradually add “PolyGlaze Plaster” in it. Mix the product with approximately 18 – 20% of water. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. Protect the paste from heat and use within 30 minutes of preparation Do’s about “PolyGlaze Plaster”: Apply the mix to the surface using a steel trowel in a smooth even motion working from the base of the surface upwards to reduce wastage. Apply the mix with a trowel, followed by a second levelling if required. Once the surface is uniform, level with a wooden/fiber/ steel/plastic float to produce a smooth even surface. Water curing for 3-4 days should be carried out prior to any subsequent application depending on the moisture level of the surface. Don’ts about “PolyGlaze Plaster” : Do not apply straight on to gypsum panels. Do not use in damp areas. Do not add water to make it workable, prepare a fresh mixture. Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Plaster” should be stored in a dry place. Although “PolyGlaze Plaster” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. Incase of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze Plaster” PRODUCT INFORMATION FORM Dry powder COLOUR & TEXTURE Greyish Granular BINDER Ordinary Portland cement 53 Grade AGGREGATE Graded Sand PACKAGING 40 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 18-20% by weight POTLIFE Approx. 30 minutes COVERAGE 0.16 – 0.23 kg/ sq.ft/ mm or 17 – 25 sq.ft at 10 mm thickness per 40 kg bag PERFORMANCE INFORMATION COMPRESSIVE STRENGTH ≥4 N/mm2 N/mm2 after 28 days CURING TIME 5 – 6 Days COAT THICKNESS 8 – 25 mm COMPATIBILTY Any good Quality Wall Putty/Paints etc can be used over Polyglaze Plaster
PolyGlaze Jointing Mortar “PolyGlaze Jointing Mortar” is a thin bed, high strength, pre-mixed, quality assured mortar comprising of Ordinary Portland Cement, specially graded sand and Polymers. It is specially formulated and easily applied, giving a better bonding with higher air entraining properties. “PolyGlaze Jointing Mortar” is a masonry mortar for use in laying various types of fly ash / concrete bricks, AAC blocks and stones. It replaces conventional jointing mortar of 12-18 mm thickness with highly versatile 3-4 mm thickness mortar. Special Properties of “PolyGlaze Jointing Mortar”: Our quick setting proprietary mortar essentially “glues” the block together and the next course is ready to lay within a very short time. Higher bonding strength increases durability and eliminates future maintenance. Non-metallic, doesn’t rust out, will not discolor wall. Ready mixed mineral based products designed for new construction as well as for renovation purpose. Being premixed, it saves considerable time, labour and increases dimensional stability of the blocks. Being premixed and less porous, it inhibits efflorescence. Areas of use : Laying bricks and blocks: To join fly ash bricks, cement block, hollow blocks, aerated block etc. Jointing of prestressed concrete slabs, panels. Jointing of cement window and door frames. Barbecues and fire places. Garden and boundary walls. Screed and compost bins, sand pits. Bench stands, bicycle stands. Terracing. Ornamental Pools. Repairing of masonry walls. Surface Preparation : When laying new brick or block walls first construct a sound footing below the first line. All substrates should be cleaned and free from dust, oil, grease, curing agents, paints, which may affect adhesion. Wet the substrates before the application, without leaving excess water. When repairing mortar joints, remove all loose foreign materials. Preparation of “PolyGlaze Jointing Mortar”: Take a small amount of water in a bucket and gradually add “PolyGlaze Jointing Mortar” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water.). Application of “PolyGlaze Jointing Mortar”: Layout the wall you are going to work on and mark openings like door, windows, and any architectural appurtenances, you are including in your design. Put a thin layer of Jointing Mortar in the thickness of 3 to 4 mm on the clean and leveled surface using proper trowel on which the block work is to be carried out. Place the block on the laid jointing mortar in proper line and level. After placing the first block apply the jointing mortar of the same thickness i.e 3-4 mm for both horizontal and vertical joint of the block. Space “mortar boards” about every six feet along the wall, or on each side if the project is small. Brush the face of the brick with a foxtail brush to wipe away excess mortar and finish smoothing the joint. Continue laying the brick with 3-4mm thickness of jointing mortar until you are levelled with the leads you laid up. Filling the joint : Spread the mortar across the whole surface using the rubber blade of the trowel and work thoroughly into the joints. Brushing Off : After approximately 10-15 minutes, the mortar should have achieved a semi-dry consistency. Don’t brush this residual mortar into any unfilled joints. Useful Tips : It should be kept in dry place. Keep out of reach of children. Avoid inhalation of dust. Use proper tools while cutting blocks. Tools should be thoroughly cleaned in water to remove excess materials immediately after use. Technical Information: “PolyGlaze Jointing Mortar” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 40 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS Approx 25% by Weight POT LIFE Approx. 45 minutes HARD DRY 24 hours BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48hours (depending on site conditions) COVERAGE Approx 200 sq.ft/ 40 kg bag @ 3-4mm bed thickness (100mm AAC Blocks) PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH 0.60(MV)MPa as per ASTM D 4541 on Concrete block after 28 days 0.55(MV)MPa as per ASTM D 4541 on AAC block after 28 days COMPRESSIVE STRENGTH > 4 N/mm2 as per IS 4031 P.6 after 7 days FLEXURAL STRENGTH >5.5 N/mm2 as per ASTM C 580 after 3 days SELF CURING Yes, No additional Curing is required 14
PolyGlaze White Tile Adhesive “PolyGlaze White Tile Adhesive” is a thin set, multipurpose, polymer fortified white adhesive offering vast utility including applications on interior floors & wall as well as limited exterior floor & wall installations. It can be used for fixing any porosity tile and natural stones like glass mosaic marble, granite on new / old substrates. Special Properties of PolyGaze White Tile Adhesive : It is ready to use mix; single component product, just add water in specified proportion and apply. High tensile adhesion strength. Being ready to use material, it saves considerable time and labour. Polymer modified formulation enhances its durability. Grouting is possible on the same day. Self-curing property helps in reducing shrinkage cracks. Recommended Substrate : Cement mortar bed. Ceramic tiles and Natural Stones – Walls & floors. Cement terrazzo Concrete Block. Application Procedure : Surface Preparation : The surface should be clean, dry and free from dust, grease/oil and other contaminants. As Polyglaze White Tile Adhesive is a thin set adhesive, be ensure that substrate surface is leveled to minimize the consumption. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze White Tile Adhesive”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fiber cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze White Tile Adhesive” : Take a small amount of water in a bucket and gradually add “PolyGlaze White Tile Adhesive” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done mechanically by stirrer or manually by hand. Mixing to be done till homogenous lump free mix is obtained. After mixing, leave the paste for 5-10 minutes for polymeric dispersion. The paste should be kept away from direct sunlight, heat and should be used within 30 minutes of preparation (after mixing with water). Application of “PolyGlaze White Tile Adhesive” : Before fixing the tiles, natural stones, etc., clean the backside of these with wet cloth to remove all dust and loose particles. Apply mortar to the substrate with the flat side of trowel, pressing firmly to work into surface. Comb on additional mortar with the notched side. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive from the face of the tiles. Any adjustment should be done within 20 – 30 minutes of application and before adhesive start hardening. Wait for at least 12 hours for the setting of tile adhesive before grouting. Caution : Store above the ground in Dry condition. During cold weather, protect the finished surface from traffic until fully set. Avoid contact with eyes or prolonged contact with skin. In case of irritation, rinse thoroughly with water. Keep out of reach of the children. Technical Information: “PolyGlaze White Tile Adhesive” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR White PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 30 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 55-60 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1 N/mm2 after 28 days SELF CURING Yes, no additional curing is required
PolyGlaze Wall Putty “PolyGlaze Wall Putty” is a white cement based putty, ideal for use on concrete/mortar, internal/external walls and Ceilings. It fills the fine pores of mortar/concrete walls and ceilings and provides a white, smooth and dry surface essential for painting. It gives excellent adhesive strength, durability and enhances the life of paints. Special properties of “PolyGlaze Wall Putty” : It can be applied on both Interior and Exterior surfaces. It does not require any curing. It can be used on new as well as old walls/ceilings. It will give a smooth and glossy finish. Any kind of Paint or Distemper can be applied on it. It prevents the growth of algae and fungi on walls. “Polyglaze Wall Putty” is water and UV resistant. Application Procedure : Surface Preparation: Substrate should be clean and free from dust, oil, grease, curing agent, paints, which may affect the adhesion. Remove all the loosely adhered material from the wall surface with the help of emery stone or wire brush and clean water. Properly cure the dry surface with the sufficient quantity of clean water before application of putty. Mixing of “PolyGlaze Wall Putty”: Take water in bucket and gradually add “PolyGlaze Wall Putty” in it. Mix the product with water in the ratio of approximately 1:3. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump-free paste is obtained. After mixing leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 30 minutes of preparation (after mixing with water). Re-mix the paste again before application. Application of “PolyGlaze Wall Putty”: TApply the first coat of “PolyGlaze Wall Putty” on already moistened wall surface from bottom to upward direction with the help of putty trowel. Allow the first coat of putty to dry for atleast for 3 hours before application of second coat of putty. Apply the second coat of putty from bottom to upward direction. Allow the second coat to dry completely for 12 hours. The total thickness of coat should not exceed more than 2 mm. Rub the surface very gently with very fine emery paper before application of paint. Precautions during Application: Take extreme care in mixing the “PolyGlaze Wall Putty” with hand or mechanical stirrer in order to get best results. Application should be done on fully cured surface. Do not rub “PolyGlaze Wall Putty” harshly with rough emery paper. Total thickness should not be more than 2 mm. Always prepare the required quantity of material which can be used within 30 minutes after preparation. Precaution During Usage : Avoid dust inhalation during mixing and handling of “PolyGlaze Wall Putty”. In case of contact with eyes, rinse eye with plenty of water. Keep in a dry place and out of reach of children. People with allergy to cement should take proper precaution Technical Information: “PolyGlaze Wall Putty” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR White PACKAGING 20 kg & 40 kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 30-35% by weight POT LIFE Approx. 30 minutes SETTING TIME: INITIAL (Minutes) 100 minutes SETTING TIME: FINAL (Minutes) 500 minutes COVERAGE 18-20 sq.ft/ kg/mm PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1 N/mm2 after 28 days SHRINKAGE 1.5 mm/m after 28 days COMPRESSIVE STRENGTH > 4 N/mm2 after 28 days FLEXURAL STRENGTH > 4 N/mm2 after 28 days WATER ABSORPTION 0.3 ml after 1 hour as per KARSTEN TUBE TEST *Testing as per IS: 12808-2 & EN 1348
PolyGlaze Tile Adhesive – XT “PolyGlaze Tile Adhesive – XT” is a cementitious readymix powder which is thin-bed and a high tensile polymer modified product. Its unique properties make it ideal for fixing ceramic tiles / vitrified tiles /mosaic tiles / natural stones like granite, marble etc., to most building substrates. Special Properties of “PolyGlaze Tile Adhesive - XT” : Preparation is simple, just add water. Although cement based, requires no curing. It can be used in damp areas. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix wall and floor tiles, natural stones like granite, marble etc. Cementitious screeds. Cement Mortar beds. Bathrooms and kitchens. Fixing the facades. Swimming pools. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5 – 7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – XT”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - XT”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – XT” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - XT”: Before fixing the tiles, natural stones etc., clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes and before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - XT”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – XT” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left round each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive- XT” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “Polyglaze Tile Adhesive XT” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 60 – 70 sq.ft/ 20 kg bag @ 3 – 4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required
PolyGlaze Tile Adhesive – Floor “PolyGlaze Tile Adhesive – Floor” is a cementitious readymix powder which is thin-bed and olymer modified product. Its unique properties make it ideal for fixing ceramic tiles, vitrified tiles, mosaic tiles and other floor tiles. Special Properties of “PolyGlaze Tile Adhesive - Floor” : Preparation is simple, just add water. Although cement based, requires no curing. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix floor tiles like ceramic, vitrified, mosaic and other floor tiles. Cementitious screeds. Cement Mortar beds. Bathrooms, kitchens etc. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure, prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – Floor”. Remove curing compounds, if any, from the surface. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - Floor”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – Floor” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - Floor”: Before fixing the tiles, clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - Floor”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – Floor” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left around each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive – Floor” is nonhazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze Tile Adhesive - Floor” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 45 – 55 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required Evershine Build India Private Limited HOME ABOUT US OUR PRODUCTS PolyGlaze Tile Adhesive – Floor PolyGlaze Tile Adhesive – XT PolyGlaze XT – Flex PolyGlaze White Tile Adhesive PolyGlaze Tile Grout PolyGlaze Jointing Mortar PolyGlaze Plaster PolyGlaze Wall Putty PolyGlaze Crack ‘O’ Fill PolyGlaze Repair Mortar EVENTS BRANDING OUR CLIENTELE CONTACT US Copyright © 2015 Evershine Build India Pvt Ltd
PolyGlaze XT – Flex “PolyGlaze XT – Flex (Grey/White)” is a multipurpose cementitious ready-mix powder, which is thin-bed and a high tensile polymer modified product. Its unique properties make it ideal for fixing tiles & natural stones like granite, marble on plywood, metal surface and wall cladding. Special Properties of “PolyGlaze XT - Flex”: Ready to mix, single component product. Preparation is simple, just add water. Although cement based, requires no curing. It can be used in damp areas. Very high tensile adhesion strength. It is suitable for heavy duty application with moderate structural movements. It is suitable for fibre cement boards, wooden floor for both interior and exteriar surfaces. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix wall and floor tiles, natural stones like granite, marble on seasoned wood, metal surface, heavy duty applications like wall cladding at vertical surface. Cementitious screeds. Cement Mortar beds. Bathrooms and kitchens. Fixing the facades. Swimming pools. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow at least 4 weeks for concrete to cure prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze XT – Flex”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze XT - Flex”: Take a small amount of water in a bucket and gradually add “PolyGlaze XT – Flex” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 30 minutes of preparation (after mixing with water). Do’s about “PolyGlaze XT - Flex”: Before fixing the tiles, natural stones etc., clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 15-20 minutes and before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze XT - Flex”: Avoid very high speed mixing when electric mixing equipments are used. Coverage : 50 – 60 sq.ft per 20 Kg. bag with notch trowel for a bed of 3 – 4 mm thickness. Please note that coverage will depend upon the undulation of base substrate and thickness of material used. Useful Tips : “PolyGlaze XT – Flex” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left around each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze XT – Flex” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze XT - Flex” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey / White PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 30 minutes OPEN TIME 15 – 20 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48hours (depending on site conditions) COVERAGE 60 – 70 sq.ft/ 20 kg bag @ 3 – 4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH Approx>2 N/mm2 after 28 days SELF CURING Yes, no additional curing is required
Tile & Stone Installations, Tile & Stone Adhesives, Tile Joint Grouts, Tile & Stone care, Wall levelling compound, Tile & stone Adhesives, Tile Joint Grouts, Polymer Modified Grout for Wall & Floor Tile Joints, Super Grout, Wide Joint Grout, ADMIX GT, Liquid Polymer Additive For Use With Cement Based Grout, Concrete Repair, Anchors & Grouts, Concrete Repair & Protection, ARDEX ENDURA,
Tile Adhesive Suppliers in Chennai , Wall Putty Suppliers in Chennai , Tile Epoxy Grout Distributor in Chennai , Tile Cement Grout Distributor in Chennai , ACC Block Joint Mortar Distributor in Chennai , Rapier Mortar Distributor in Chennai , Readymade Wall Plaster Dealer in Chennai , Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Myk Laticrete, Tile Adhesive Suppliers in Chennai , Wall Putty Suppliers in Chennai , Myk Laticrete Tile Epoxy Grout Distributor in Chennai , Tile Cement Grout Distributor in Chennai , ACC Block Joint Mortar Distributor in Chennai , Rapier Mortar Distributor in Chennai , Readymade Wall Plaster Dealer in Chennai , Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Tiles Adhesive Wholesale Suppliers in Madhuravoyal : Tiles Adhesive Wholesale Suppliers in Poonamallee , Tiles Adhesive Wholesale Suppliers in Avadi , Tiles Adhesive Wholesale Suppliers in CMBT , Tiles Adhesive Wholesale Suppliers in Mogappair , Tiles Adhesive Wholesale Suppliers in Anna Nagar , Tiles Adhesive Wholesale Suppliers in Kolathur , Tiles Adhesive Wholesale Suppliers in T Nagar , Tiles Adhesive Wholesale Suppliers in Pusaivakkam , Tiles Adhesive Wholesale Suppliers in Tynampet , Tiles Adhesive Wholesale Suppliers in Mylapore , Tiles Adhesive Wholesale Suppliers in Tambaram , Tiles Adhesive Wholesale Suppliers in Guindy , Tiles Adhesive Wholesale Suppliers in Velachery , Tiles Adhesive Wholesale Suppliers in Porur , Tiles Adhesive Wholesale Suppliers in Koyambedu , Tiles Adhesive Wholesale Suppliers in Padi , Tiles Adhesive Wholesale Suppliers in Chennai . Wall Putty Suppliers in Maduravoyal , Wall Putty Suppliers in Chennai , Wall Putty Suppliers in Anna Nagar , Wall Putty Suppliers in Moggapair , Wall Putty Suppliers in Koyamabedu , Wall Putty Suppliers in Arumbakkam , Tile Adhesive Suppliers in Chennai , Wall Putty Suppliers in Chennai , Tile Epoxy Grout Distributor in Chennai , Tile Cement Grout Distributor in Chennai , ACC Block Joint Mortar Distributor in Chennai , Rapier Mortar Distributor in Chennai , Readymade Wall Plaster Dealer in Chennai , Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Myk Laticrete, Tile Adhesive Suppliers in Chennai , Wall Putty Suppliers in Chennai , Tile Epoxy Grout Distributor in Chennai , Tile Cement Grout Distributor in Chennai , ACC Block Joint Mortar Distributor in Chennai , Rapier Mortar Distributor in Chennai , Readymade Wall Plaster Dealer in Chennai , Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Tile Adhesive Suppliers in Chennai , Wall Putty Suppliers in Chennai , Tile Epoxy Grout Distributor in Chennai , Tile Cement Grout Distributor in Chennai , ACC Block Joint Mortar Distributor in Chennai , Rapier Mortar Distributor in Chennai , Readymade Wall Plaster Dealer in Chennai , Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Myk laticrete, Tile Adhesive Suppliers in Chennai , Myk Laticrete Wall Putty Suppliers in Chennai , Myk Laticrete Tile Epoxy Grout Distributor in Chennai , Myk Laticrete Tile Cement Grout Distributor in Chennai , Myk Laticrete ACC Block Joint Mortar Distributor in Chennai , Myk Laticrete Rapier Mortar Distributor in Chennai , Myk Laticrete Readymade Wall Plaster Dealer in Chennai , super mastice Teemax Marble Joint Chemical and Tools Granite Chemical Italian Marble Chemical Marble Epoxy Cleaner in Chennai etc Tile & Stone Installations, Tile & Stone Adhesives, Tile Joint Grouts, Tile & Stone care, Wall levelling compound, Tile & stone Adhesives, Tile Joint Grouts, Polymer Modified Grout for Wall & Floor Tile Joints, Super Grout, Wide Joint Grout, ADMIX GT, Liquid Polymer Additive For Use With Cement Based Grout, Concrete Repair, Anchors & Grouts, Concrete Repair & Protection, ARDEX ENDURA,
1
false