http://WWW.KUSHALENTERPRISES.NET
KUSHULENTERPRISES 5858e9f8b40a780a242d8ccc False 259 14
OK
background image not found
Found Update results for
'polyglaze tile adhesive'
9
PolyGlaze Tile Adhesive – Floor “PolyGlaze Tile Adhesive – Floor” is a cementitious readymix powder which is thin-bed and olymer modified product. Its unique properties make it ideal for fixing ceramic tiles, vitrified tiles, mosaic tiles and other floor tiles. Special Properties of “PolyGlaze Tile Adhesive - Floor” : Preparation is simple, just add water. Although cement based, requires no curing. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix floor tiles like ceramic, vitrified, mosaic and other floor tiles. Cementitious screeds. Cement Mortar beds. Bathrooms, kitchens etc. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure, prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – Floor”. Remove curing compounds, if any, from the surface. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - Floor”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – Floor” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - Floor”: Before fixing the tiles, clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - Floor”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – Floor” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left around each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive – Floor” is nonhazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “PolyGlaze Tile Adhesive - Floor” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 45 – 55 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required Evershine Build India Private Limited HOME ABOUT US OUR PRODUCTS PolyGlaze Tile Adhesive – Floor PolyGlaze Tile Adhesive – XT PolyGlaze XT – Flex PolyGlaze White Tile Adhesive PolyGlaze Tile Grout PolyGlaze Jointing Mortar PolyGlaze Plaster PolyGlaze Wall Putty PolyGlaze Crack ‘O’ Fill PolyGlaze Repair Mortar EVENTS BRANDING OUR CLIENTELE CONTACT US Copyright © 2015 Evershine Build India Pvt Ltd
PolyGlaze Tile Adhesive – XT “PolyGlaze Tile Adhesive – XT” is a cementitious readymix powder which is thin-bed and a high tensile polymer modified product. Its unique properties make it ideal for fixing ceramic tiles / vitrified tiles /mosaic tiles / natural stones like granite, marble etc., to most building substrates. Special Properties of “PolyGlaze Tile Adhesive - XT” : Preparation is simple, just add water. Although cement based, requires no curing. It can be used in damp areas. High tensile adhesion strength. Grouting is possible on the same day. Polymer modified formulation enhances its durability. Being ready to use, the product saves considerable time and labour. Areas of Use: To fix wall and floor tiles, natural stones like granite, marble etc. Cementitious screeds. Cement Mortar beds. Bathrooms and kitchens. Fixing the facades. Swimming pools. Surface Preparation : The surface should be clean, dry, and free from dust, grease / oil and other contaminates. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5 – 7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze Tile Adhesive – XT”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fibre cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze Tile Adhesive - XT”: Take a small amount of water in a bucket and gradually add “PolyGlaze Tile Adhesive – XT” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done manually or by stirrer. Mixing to be done till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5-10 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and used within 45 minutes of preparation (after mixing with water). Do’s about “PolyGlaze Tile Adhesive - XT”: Before fixing the tiles, natural stones etc., clean the backsides of these with wet cloth to remove all dust particles. Apply a layer of adhesive on the substrate and spread it by notch trowel. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive on the face of the tiles. Any adjustment should be done within 20 – 30 minutes and before adhesive starts hardening. Wait for at least 12 hours before grouting for better contact. Don’ts about “PolyGlaze Tile Adhesive - XT”: Avoid very high speed mixing when electric mixing equipments are used. Useful Tips : “PolyGlaze Tile Adhesive – XT” should be stored in a dry place. It is recommended that when fixing tiles, a minimum spacing of 3mm should be left round each tile. Excess adhesive should be removed using a damp sponge or cloth before material has set. Floors will be ready to receive light foot traffic after 24 hours and can be put into full use after 72 hours. Although “PolyGlaze Tile Adhesive- XT” is non-hazardous, following precautions should be adhered: Keep out of reach of the children. Avoid inhalation of dust. In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately. Technical Information: “Polyglaze Tile Adhesive XT” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR Grey PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 45 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 60 – 70 sq.ft/ 20 kg bag @ 3 – 4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1N/mm2 after 28 days SELF CURING Yes, no additional curing is required
PolyGlaze White Tile Adhesive “PolyGlaze White Tile Adhesive” is a thin set, multipurpose, polymer fortified white adhesive offering vast utility including applications on interior floors & wall as well as limited exterior floor & wall installations. It can be used for fixing any porosity tile and natural stones like glass mosaic marble, granite on new / old substrates. Special Properties of PolyGaze White Tile Adhesive : It is ready to use mix; single component product, just add water in specified proportion and apply. High tensile adhesion strength. Being ready to use material, it saves considerable time and labour. Polymer modified formulation enhances its durability. Grouting is possible on the same day. Self-curing property helps in reducing shrinkage cracks. Recommended Substrate : Cement mortar bed. Ceramic tiles and Natural Stones – Walls & floors. Cement terrazzo Concrete Block. Application Procedure : Surface Preparation : The surface should be clean, dry and free from dust, grease/oil and other contaminants. As Polyglaze White Tile Adhesive is a thin set adhesive, be ensure that substrate surface is leveled to minimize the consumption. Concrete Floors and Walls : Allow 3 – 4 weeks for concrete to cure prior to tiling. Screeds must be 5-7 days old and properly cured. The surface should be properly leveled for best results of “PolyGlaze White Tile Adhesive”. Remove curing compounds, if any, from the surface. Existing Tiles: Existing tiles must be roughened mechanically with wire brush. Painted Surfaces: Oil-based paint should be removed by roughening mechanically and loose flaking paint should be removed completely. Allow the surface to dry after cleaning. Fibre Cement Sheets: Fiber cement sheets must be primed with water and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Preparation of “PolyGlaze White Tile Adhesive” : Take a small amount of water in a bucket and gradually add “PolyGlaze White Tile Adhesive” in it. Mix the product with water in the ratio of approximately 1:4. Mixing can be done mechanically by stirrer or manually by hand. Mixing to be done till homogenous lump free mix is obtained. After mixing, leave the paste for 5-10 minutes for polymeric dispersion. The paste should be kept away from direct sunlight, heat and should be used within 30 minutes of preparation (after mixing with water). Application of “PolyGlaze White Tile Adhesive” : Before fixing the tiles, natural stones, etc., clean the backside of these with wet cloth to remove all dust and loose particles. Apply mortar to the substrate with the flat side of trowel, pressing firmly to work into surface. Comb on additional mortar with the notched side. Lay the tiles/stones and press firmly. Then knock properly with rubber hammer in order to spread the adhesive equally and for a good contact. Remove any surplus adhesive from the face of the tiles. Any adjustment should be done within 20 – 30 minutes of application and before adhesive start hardening. Wait for at least 12 hours for the setting of tile adhesive before grouting. Caution : Store above the ground in Dry condition. During cold weather, protect the finished surface from traffic until fully set. Avoid contact with eyes or prolonged contact with skin. In case of irritation, rinse thoroughly with water. Keep out of reach of the children. Technical Information: “PolyGlaze White Tile Adhesive” PRODUCT INFORMATION FORM Dry powder STANDARD COLOUR White PACKAGING 20 Kg PP Bags STORAGE CONDITIONS Store in a dry place SHELF LIFE 6 months in unopened manufacturer’s packaging APPLICATION INFORMATION MIX PROPORTIONS 20-25% by weight POT LIFE Approx. 30 minutes OPEN TIME 20 – 30 minutes BED THICKNESS 3 – 4 mm TIME TO TRAFFIC Grout after 12 hours; light foot traffic after 24 hours; Full traffic after 48 hours (depending on site conditions) COVERAGE 55-60 sq.ft/ 20 kg bag @ 3-4mm thickness PERFORMANCE INFORMATION TENSILE ADHESION STRENGTH >1 N/mm2 after 28 days SELF CURING Yes, no additional curing is required
polyglaze stone tiles adhesive 20kg bag
Myk laticrete and poly glaze tile adhesive floor thin set adhesive white flex white wallputty joint mortar cement grout plaster etc materials ableable here
We are the Leading Wholesale Supplier of Tile Adhesive in Tamil Nadu
polyglaze tile epoxy grout 5.5kg
Kushal Enterprises No.10 saroja complex sanathi street maduravoyal market chennai Near by murugan store Phone no 9884177503 Destibutor of poly glaze And laticrete tile adhesive wallputty epoxy grout cement grout and marble chemical etc materials
Myk laticrete thin set adhesive 252 white 20kg bag application for. marble granite Italian marble wet cladding and wall tales fixing
1
false